How to Set Up a Weight Distribution Hitch (WDH)
Hooking up a travel trailer for a trip down I-95 or out toward Lake Okeechobee should be exciting, not nerve-wracking. However, if your tow vehicle’s rear bumper is sagging, your front tires feel floaty, or every passing semi-truck causes your trailer to fishtail, your hitch setup needs attention.
Learning how to set up a weight distribution hitch properly is one of the most critical safety steps for any travel trailer owner. A correctly adjusted Weight Distribution Hitch (WDH) leverage-shifts heavy tongue weight off your truck’s rear axle and redistributes it evenly across your front steering axle and the trailer’s axles.
Follow this step-by-step travel trailer hitch walkthrough to dial in your shank height, spring bar tension, and sway control for a smooth, level ride.
Tools You Will Need Before Starting
- Flat, level concrete surface (do not perform this on grass or gravel)
- Measuring tape
- Socket wrench set & torque wrench
- Work gloves
- Your tow vehicle loaded with typical gear/passengers and travel trailer loaded to towing weight
Step 1: Measure Your Baseline Truck Height
Before dropping your trailer coupler onto the hitch ball, establish baseline measurements for your tow vehicle.
- Park your truck on level ground in a straight line.
- Measure the distance from the ground to the top edge of the front wheel well arch. Write this number down as your Front Uncoupled Baseline.
- Measure from the ground to the rear wheel well arch. Write this down as your Rear Uncoupled Baseline.
Crucial Safety Rule: The goal of a WDH is to return your front wheel well height as close as possible to its original baseline measurement. If the front end rises significantly when hitched, you lose steering control and braking traction.
Step 2: Level the Travel Trailer & Measure Coupler Height
Next, get your travel trailer perfectly level to determine your hitch ball height.
- Use your trailer tongue jack to raise or lower the front of the camper until the frame is level front-to-back (verify with a bubble level on the trailer frame).
- Measure from the ground to the inside top of the trailer’s coupler socket. Write this down as your Target Ball Height.
Step 3: Adjusting WDH Height on the Shank
Now assemble your hitch head on the adjustable shank receiver.
- Insert the hitch shank into your truck’s receiver hitch and secure it with the hitch pin.
- Position the hitch ball platform on the shank so that the top of the hitch ball sits 1 to 2 inches higher than your measured Target Ball Height. (Why? The truck and trailer will compress slightly once the full load rests on the system).
- Insert the mounting bolts through the hitch head and shank, but leave them hand-tight for now so you can adjust the head tilt angle.
Step 4: Set the Head Tilt Angle & Mount Spring Bars
Most WDH systems (like Equal-i-zer, CURT, or Blue Ox) use a series of washers or a rivet angle-set pin to tilt the hitch head slightly backward toward the trailer. This tilt dictates how much leverage your spring bars will apply.
- Insert 4 to 6 washer shims onto the rivet pin behind the hitch head (consult your specific manufacturer’s manual for starting defaults).
- Couple your travel trailer onto the hitch ball and lock the coupler latch.
- Use the trailer tongue jack to raise both the trailer and the rear of the truck together 3 to 5 inches. Pro-Tip: Lifting the connected vehicle pair takes the tension off the system, making spring bar attachment easy and safe.
- Insert the spring bars into the hitch head sockets and swing them into place over the L-brackets or chain perches mounted on the trailer frame.
- Secure the spring bars with the retaining pins, then lower the tongue jack completely so the full weight rests on the hitch.
Step 5: Verify Measurements & Adjust Tension
With the full weight resting on the connected system, re-measure your front and rear wheel wells:
- Ideal Result: Your front wheel well measurement should be within 1/16″ to 1/2″ of your original uncoupled baseline measurement.
- Under-Distributed (Front End Too High): If the front of your truck is still sitting higher than the baseline, you need more leverage. Raise the tongue jack, add 1-2 more washer shims to increase head tilt, or raise the L-brackets on the trailer frame.
- Over-Distributed (Front End Lower Than Baseline): If your front end is squatted lower than its original height, you have too much tension. Remove a washer shim or drop the frame brackets down one notch.
Step 6: Fine-Tune Your RV Sway Control Setup
Integrated rv sway control setup varies depending on your hitch style:
- 2-Point / 4-Point Friction Sway Hitches: Friction pads on the frame brackets prevent sway natively. Ensure brackets are installed between 27 and 32 inches back from the center of the coupler and torqued strictly to factory specs.
- Independent Sway Bars: If using an add-on friction sway bar, mount the mini-ball to your hitch head and trailer frame. Tighten the friction control handle until stiff, but remember to loosen or remove independent sway bars when backing into tight campsite spots or maneuvering during wet weather.
Once your measurements match up, tighten all shank bolts and hitch hardware to the manufacturer’s specified foot-pounds using a torque wrench.
Need Help Setting Up Your Rig?
Setting up a weight distribution hitch can be tricky without the proper tools or heavy-duty torque equipment. If you want peace of mind before heading out on your next Florida adventure, the service team at Sun Camper RV is here to help.
Bring your tow vehicle and travel trailer to our service bays in Fort Pierce or Okeechobee, and our technicians will properly spec, torque, and level your hitch setup. Browse our full inventory of half-ton towables, couples coaches, and lightweight travel trailers today!
